diff --git "a/rt-thread-version/rt-thread-standard/tutorial/make-bsp/renesas-ra/RA\347\263\273\345\210\227\351\251\261\345\212\250\344\273\213\347\273\215.md" "b/rt-thread-version/rt-thread-standard/tutorial/make-bsp/renesas-ra/RA\347\263\273\345\210\227\351\251\261\345\212\250\344\273\213\347\273\215.md" index b125bf0c947140edb3675578ebce28a9709f66fe..5c1b7c4d3b4e9dc892ffbc57663768a5b394146e 100644 --- "a/rt-thread-version/rt-thread-standard/tutorial/make-bsp/renesas-ra/RA\347\263\273\345\210\227\351\251\261\345\212\250\344\273\213\347\273\215.md" +++ "b/rt-thread-version/rt-thread-standard/tutorial/make-bsp/renesas-ra/RA\347\263\273\345\210\227\351\251\261\345\212\250\344\273\213\347\273\215.md" @@ -30,17 +30,17 @@ | 驱动 | 简介 | | ------------------------------------------------------------ | ------------------------------------------------ | -| [GPIO](https://www.rt-thread.org/document/site/programming-manual/device/pin/pin/) | 操作 GPIO 管脚 | -| [UART](https://www.rt-thread.org/document/site/programming-manual/device/uart/uart/) | 通过串口收发数据 | -| [I2C](https://www.rt-thread.org/document/site/programming-manual/device/i2c/i2c/) | 通过软件 I2C 收发数据 | -| [SPI](https://www.rt-thread.org/document/site/programming-manual/device/spi/spi/) | 通过 SPI 收发数据 | -| [ADC](https://www.rt-thread.org/document/site/programming-manual/device/adc/adc/) | 测量管脚上的模拟量 | +| [GPIO](https://www.rt-thread.org/document/site/#/rt-thread-version/rt-thread-standard/programming-manual/device/pin/pin) | 操作 GPIO 管脚 | +| [UART](https://www.rt-thread.org/document/site/#/rt-thread-version/rt-thread-standard/programming-manual/device/uart/uart_v1/uart) | 通过串口收发数据 | +| [I2C](https://www.rt-thread.org/document/site/#/rt-thread-version/rt-thread-standard/programming-manual/device/i2c/i2c) | 通过软件 I2C 收发数据 | +| [SPI](https://www.rt-thread.org/document/site/#/rt-thread-version/rt-thread-standard/programming-manual/device/spi/spi) | 通过 SPI 收发数据 | +| [ADC](https://www.rt-thread.org/document/site/#/rt-thread-version/rt-thread-standard/programming-manual/device/adc/adc) | 测量管脚上的模拟量 | | SDIO | 通过 SDIO 读写数据 | -| [TIMER](https://www.rt-thread.org/document/site/programming-manual/device/hwtimer/hwtimer/) | 使用硬件定时器实现测量时间和定时执行回调函数功能 | -| [PWM](https://www.rt-thread.org/document/site/programming-manual/device/pwm/pwm/) | 在特定的管脚输出 PWM 波形 | -| [RTC](https://www.rt-thread.org/document/site/programming-manual/device/rtc/rtc/) | 设置和读取时间 | -| [WDT](https://www.rt-thread.org/document/site/programming-manual/device/watchdog/watchdog/) | 看门狗驱动 | -| [QSPI](https://www.rt-thread.org/document/site/programming-manual/device/spi/spi/#qspi_1) | 通过 SPI（1、2、4线） 收发数据 | +| [TIMER](https://www.rt-thread.org/document/site/#/rt-thread-version/rt-thread-standard/programming-manual/device/hwtimer/hwtimer) | 使用硬件定时器实现测量时间和定时执行回调函数功能 | +| [PWM](https://www.rt-thread.org/document/site/#/rt-thread-version/rt-thread-standard/programming-manual/device/pwm/pwm) | 在特定的管脚输出 PWM 波形 | +| [RTC](https://www.rt-thread.org/document/site/#/rt-thread-version/rt-thread-standard/programming-manual/device/rtc/rtc) | 设置和读取时间 | +| [WDT](https://www.rt-thread.org/document/site/#/rt-thread-version/rt-thread-standard/programming-manual/device/watchdog/watchdog) | 看门狗驱动 | +| [QSPI](https://www.rt-thread.org/document/site/#/rt-thread-version/rt-thread-standard/programming-manual/device/spi/spi?id=配置-qspi-设备) | 通过 SPI（1、2、4线） 收发数据 | ### 2.2 板载外设